We value your privacy

Our website uses cookies to enhance your experience. By continuing to use our website, you are agreeing to our use of cookies. Necessary cookies are always enabled. You can read more about our Cookie Policy in our Privacy policy

We value your privacy

FibreGlassDirect - Buy Fiberglass Supplies & Materials

Shopping Cart 0
£0.00

B260 Raised Edge Roofing Trim

In stock
Only %1 left
SKU
conf_b260_raised_edge_roofing_trim
As low as £15.84 £13.20

Fitted to the roof edge, this trim prevents water run off. This trim is compatible with the A200 Drip Roofing Trim.

Dimensions

Girth: 260mm, Depth: 125mm, Length: 1.5 metres / 3 metres

A single batten is fixed level with the top edge of the deck. Apply 30mm beads of trim adhesive to the batten every 300mm, rub the trim into place and nail through the top of the trim into the decking. Do not nail through the front of the trim. 

If a ladder is likely to be leaning up against a B type trim for regular access to the roof, the trim will need to be reinforced to avoid deformation. The trim can either be doubled up by slotting a section of extra trim within the section where the ladder will be used or it can be reinforced with an extra layer of GRP laminate and then tissue to maintain a smooth finish. Alternatively, a wooden batten can be shaped and fitted into the ridge of the trim to ensure that it remains rigid.

This trim is compatible with the A200 Drip Roofing Trim.

View all of our FibreGlass Roofing Trims

Ask a Question
The following trims are compatible with each other
  • A200 is a fascia trim for allowing drainage into a gutter. Compatible with C1 C2 and C4 corner trims
  • B260 is a raised edge trim which prevents water runoff. Compatible with C1 C2 and C4 corner trims
  • A200 and the B260 are compatible with each other
  • A250 and B300 - A250 is a fascia trim for allowing drainage into a gutter & the B300 is a raised edge trim which prevents water runoff
Read more
Published in: Roofing Trims

A drip trim is placed at the lowest edge of the roof and is used to allow the water to runoff into a gutter. A raised edge trim is used to prevent the water runoff.

Published in: Roofing Trims

Roof trims should be measured and cut to size with a 'snips' (to reduce dust). A dab of roofing adhesive should be applied to the batons to prevent rattling in the wind. Roof trims should then be either stapled with s/s staples of nailed using 15mm clout nails into place every 120-150mm. Where two trims have to be joined together, ensure an overlap of 50mm and apply roofing adhesive to seal.

Published in: Roofing Trims

It is recommended that 15mm galvanised clout nail is used or s/s staples that will sit flush with the roof.

Published in: Roofing Trims
Sand an area of about 50mm around the crack using rough grit sandpaper to create a key. Clean down with acetone. Cut a piece of 450g chopped strand mat the same size as the area sanded. Cut a second piece of 450g chopped strand mat slightly smaller. Mix resin and catalyst. Brush on the resin to the area and apply the larger piece of glass. Applied more resin until the glass is fully wetted out. Apply the second layer of glass and wet out with resin using a brush. Allow the resin to cure. Once cured give the area a light sanding to remove any glass sticking up. Mix topcoat with catalyst and apply to the area with a... Read more
Published in: Roofing Trims

Whilst we would recommend GRP Trims with a fibreglass roof (the fibreglass will bond better). If you decide to use lead or metal trims, ensure the lead or metal is clean and free from contaminants. Use G4 sealer when overlapping with the fibreglass.

Published in: Roofing Trims
Brand Description
History Color sit amet, consectetur adipiscing elit. In gravida pellentesque ligula, vel eleifend turpis blandit vel. Nam quis lorem ut mi mattis ullamcorper ac quis dui. Vestibulum et scelerisque ante, eu sodales mi. Nunc tincidunt tempus varius. Integer ante dolor, suscipit non faucibus a, scelerisque vitae sapien.