1. See Detail

Fibreglass Pond Kit

SKU
conf_fibreglass_pond_kit
In stock
Quick Overview

Fibreglass Pond Kits are supplied complete with all the materials and tools needed to cover the area required with 2 layers of 450gm mat, 1 layer of 30gm glass tissue and 1 layer of topcoat.

As low as £97.66 £81.38

Fibreglass Pond Kits are supplied complete with all the materials and tools needed to cover the area required with 2 layers of 450gm mat, 1 layer of 30gm glass tissue and 1 layer of topcoat.

Fibreglass is the material of choice for lining fish ponds, It is resistant to weathering and temperature variations and is non-toxic to fish. The finished, water-tight topcoat surface is smooth and easy to clean and maintain.

Coloured topcoats can be applied, particularly black or dark green, which enhances the look of Koi swimming against a dark background.

We recommend G4 sealer when lining your pond. G4 sealer is not included in our kits but is available to buy as an optional extra.

Please note the Resin and Topcoat contained in this kit require catalyst addition to cure (set). Failure to add catalyst will result in the material not setting.

If you would like some guidance on how to install a fibreglass pond, we have written down our top tips on how to get the best results from your materials. Check them out on our blog!

Ask a Question

Use our pond calculator to calculate the surface area of your pond. You should then buy the next available size, so say for example your Pond Surface Area is 18m², you should buy a 20m² kit. For a full range of our Pond kits click here

Published in: Fibreglass Pond Lining

We have written down our top tips on adding a fibreglass lining to a concrete pond. These comprehensive guidelines will ensure you get the best results from your materials. Read about it here. 

Published in: Fibreglass Pond Lining
Using fibreglass to seal a pond made from wood and concrete? Question: I'm constructing a pond out of wooden sleepers; will be a 3m rectangle with a concrete base. Was going to use a traditional pub liner however I'm now wondering about using fibreglass. Is the product suitable for wooden walls or is brick only? FibreGlassDirect Advice:You can use the fibreglass on a wooden structure but we would advise that you used an 18mm OSB3 board inside the sleepers to fibreglass on to. A concrete base would need G4 primer (30mins before fibreglass application).   Steps to waterproofing a wooden and concrete pond with fibreglass: Line inside of sleepers with OSB3 BOARD Fibreglass bandage with resin on all board joints Apply 1 layer of 450g matting to the OSB3 board with resin, (you will need to allow 1.5kg of resin per sqm on the boards), ensuring to consolidate the laminate and remove any creases or air pockets To do the floor, you will need to apply G4 Primer / Sealer working 2 sqm at a time to the concrete and allow to go tacky (25-30mins) Whilst still tacky get a layer of 450g laminated over the tacky area. We recommend doing an area 1m right around the perimeter and if possible turning up against the walls Repeat process to remainder of floor and allow to cure Scuff the entire surface with a sanding block or sander using an 80 grit paper, brush off clean with acetone Begin to lay up of 2nd layer of 450g matting and resin (1kg of resin per sqm) Stagger the start to ensure overlap of joints Apply second layer working 2sqm at a time, consolidate well as per previous Whilst 2nd layer is still wet, you can apply a layer of surface tissue and roll on gently into the wet surface (this will provide a finer finish) Continue repeating the process until 2nd layer is complete Allow to cure and then scuff, brush and clean with acetone Mix and apply your topcoat   Leave with a temporary covering if possible to protect from rain/dampness for 2-3 days, then rinse down and fill the pond. Leave for 3-4 days, drain off and then rinse and refill.   Ready for... Read more
Published in: Fibreglass Pond Lining