D260 Wall Fillet Roofing Trim

In stock

Only %1 left

SKU

conf_d260_wall_fillet_roofing_trim

As low as £14.10 £11.75

Used where flat roof butts against existing wall and creates a 45-degree angle to deflect rainwater from wall to roof. Can also be used for gutter lining. It will also provide expansion and perimeter ventilation and is compatible with C2 and C3 universal corners.

Dimensions:

Girth: 260mm; Fillet: 135mm & 70mm; Upstand height: 120mm; Length: 1.5 metre / 3 metre

Skip to the end of the images gallery

Skip to the beginning of the images gallery

Fitting Instructions:

Place the D trim against the vertical face and push down diagonally into the corner until the trim fits snugly. Where the D trim needs to be joined it should be bonded with a strip polyurethane adhesive and bandaged together. The C trim is usually fitted into a bed joint of the brickwork or a 35/50mm (depending on the trim type) deep chase cut out with an angle grinder fitted with a mortar chase disc. Apply polyurethane adhesive to the back of the C trim every 300mm. Fit the trim into the slot and press firmly back to the wall to overlap the D trim.

Apply a clear silicone sealant along the length of the trim into the slot to seal the trim in. A smooth finish can be obtained by wiping the sealant with a moistened finger.

Ask a Question

Which roofing trims are compatible with each other?

The following trims are compatible with each other

A200 is a fascia trim for allowing drainage into a gutter. Compatible with C1 C2 and C4 corner trims
B260 is a raised edge trim which prevents water runoff. Compatible with C1 C2 and C4 corner trims
A200 and the B260 are compatible with each other
A250 and B300 - A250 is a fascia trim for allowing drainage into a gutter & the B300 is a raised edge trim which prevents water runoff

Published in: Roofing Trims

What is the best way to apply roofing trims?

Roof trims should be measured and cut to size with a 'snips' (to reduce dust). A dab of roofing adhesive should be applied to the batons to prevent rattling in the wind. Roof trims should then be either stapled with s/s staples of nailed using 15mm clout nails into place every 120-150mm. Where two trims have to be joined together, ensure an overlap of 50mm and apply roofing adhesive to seal.

Published in: Roofing Trims

Should I use special nails to secure the trims?

It is recommended that 15mm galvanised clout nail is used or s/s staples that will sit flush with the roof.

Published in: Roofing Trims

I have a crack in my GRP Roofing Trim – how do I fix it?

Sand an area of about 50mm around the crack using rough grit sandpaper to create a key. Clean down with acetone. Cut a piece of 450g chopped strand mat the same size as the area sanded. Cut a second piece of 450g chopped strand mat slightly smaller. Mix resin and catalyst. Brush on the resin to the area and apply the larger piece of glass. Applied more resin until the glass is fully wetted out. Apply the second layer of glass and wet out with resin using a brush. Allow the resin to cure. Once cured give the area a light sanding to remove any glass sticking up. Mix topcoat with catalyst and apply to the area with a... Read more

Published in: Roofing Trims

Can I use lead or metal trims with a GRP Roof?

Whilst we would recommend GRP Trims with a fibreglass roof (the fibreglass will bond better). If you decide to use lead or metal trims, ensure the lead or metal is clean and free from contaminants. Use G4 sealer when overlapping with the fibreglass.

Published in: Roofing Trims

Brand	Description
History	Color sit amet, consectetur adipiscing elit. In gravida pellentesque ligula, vel eleifend turpis blandit vel. Nam quis lorem ut mi mattis ullamcorper ac quis dui. Vestibulum et scelerisque ante, eu sodales mi. Nunc tincidunt tempus varius. Integer ante dolor, suscipit non faucibus a, scelerisque vitae sapien.