AT 195 Internal Roof Trim

In stock

SKU

conf_at_195_internal_roof_trim

As low as £15.48 £12.90

The AT195 Internal trim is used wherever the laminate needs to cover an area which continues perpendicular to another laminated surface. The AT195 Ext is supplied with a high-adhesion finish on its outer fascia and is mainly used for capping applications.

Skip to the end of the images gallery

Skip to the beginning of the images gallery

Dimensions:

Girth: 195mm; Flange widths: 85mm & 105mm

The AT195 Internal trim is used wherever the laminate needs to cover an area which continues perpendicular to another laminated surface.

The AT195 Int trim is supplied with a high adhesion finish on its outer fascia and should be used for internal corners. The trim should be nailed at both edges if possible.

Always bandage over the join between where the nails penetrate the trim and the decking before applying the laminate.

This right angled trim, with the adhesion face on the inside, is designed for forming upstands, gutters and capping parapets.

Ask a Question

Which roofing trims are compatible with each other?

The following trims are compatible with each other

A200 is a fascia trim for allowing drainage into a gutter. Compatible with C1 C2 and C4 corner trims
B260 is a raised edge trim which prevents water runoff. Compatible with C1 C2 and C4 corner trims
A200 and the B260 are compatible with each other
A250 and B300 - A250 is a fascia trim for allowing drainage into a gutter & the B300 is a raised edge trim which prevents water runoff

Published in: Roofing Trims

What is the best way to apply roofing trims?

Roof trims should be measured and cut to size with a 'snips' (to reduce dust). A dab of roofing adhesive should be applied to the batons to prevent rattling in the wind. Roof trims should then be either stapled with s/s staples of nailed using 15mm clout nails into place every 120-150mm. Where two trims have to be joined together, ensure an overlap of 50mm and apply roofing adhesive to seal.

Published in: Roofing Trims

Should I use special nails to secure the trims?

It is recommended that 15mm galvanised clout nail is used or s/s staples that will sit flush with the roof.

Published in: Roofing Trims

I have a crack in my GRP Roofing Trim – how do I fix it?

Sand an area of about 50mm around the crack using rough grit sandpaper to create a key. Clean down with acetone. Cut a piece of 450g chopped strand mat the same size as the area sanded. Cut a second piece of 450g chopped strand mat slightly smaller. Mix resin and catalyst. Brush on the resin to the area and apply the larger piece of glass. Applied more resin until the glass is fully wetted out. Apply the second layer of glass and wet out with resin using a brush. Allow the resin to cure. Once cured give the area a light sanding to remove any glass sticking up. Mix topcoat with catalyst and apply to the area with a... Read more

Published in: Roofing Trims

Can I use lead or metal trims with a GRP Roof?

Whilst we would recommend GRP Trims with a fibreglass roof (the fibreglass will bond better). If you decide to use lead or metal trims, ensure the lead or metal is clean and free from contaminants. Use G4 sealer when overlapping with the fibreglass.

Published in: Roofing Trims

Brand	Description
History	Color sit amet, consectetur adipiscing elit. In gravida pellentesque ligula, vel eleifend turpis blandit vel. Nam quis lorem ut mi mattis ullamcorper ac quis dui. Vestibulum et scelerisque ante, eu sodales mi. Nunc tincidunt tempus varius. Integer ante dolor, suscipit non faucibus a, scelerisque vitae sapien.